Cargo Theft Prevention Checklist
Operational workflow a carrier's safety director and dispatch team run to harden facility, equipment, personnel, and in-transit security against cargo theft. Covers yard hardening, high-value load handling, route planning, and post-incident response coordination with CargoNet ...
Facility and Yard Security
-
Run the quarterly yard risk assessment
Walk the perimeter against a TAPA FSR-style checklist: fence height and condition, lighting lux at gate and drop yards, blind spots, dumpster placement against fence, gate-arm operation. Note any items where a thief with bolt cutters and 90 seconds could be inside the yard.
Collects file -
Test gate access controls and camera coverage
Verify badge readers reject deactivated cards, gate cameras capture plate and driver face at the read line, and DVR retention covers at least 30 days. Confirm after-hours alarm path to the monitoring center with a live test call.
-
Verify perimeter fencing and lighting
Walk the fence line in daylight and again after dark. Flag any sections cut, leaning, or pulled at the base; any burned-out yard lights; any pallet stacks or trailers placed near the fence that create a climb-over assist.
-
Audit yard inventory against the dispatch board
Reconcile every trailer and container on the lot against the TMS yard list. Loaded trailers without a dispatch assignment or with mismatched seal numbers are the leading indicator of an in-progress fictitious-pickup scheme.
Collects list
Equipment and Seal Controls
-
Issue ISO 17712 high-security bolt seals
Use ISO 17712 'H' classified bolt seals on all loaded trailers; barrel-lock or king-pin lock additionally on high-value loads (electronics, pharma, tobacco, food and beverage). Log seal numbers in the TMS at the time of loading, not at the gate.
Collects text -
Activate covert GPS trackers on high-value loads
Place a covert tracker (e.g., LoJack SCI, SkyBitz, Spireon) inside the load — separate from the tractor ELD and trailer telematics, which thieves disable first. Confirm last-known-position ping and geofence alerts before the truck leaves the gate.
-
Inspect tractor and trailer for tampering
Check kingpin lock, air-line glad hands, fifth-wheel release, and rear doors. Pried hinges, fresh tool marks at the door frame, or a swapped seal are pre-theft indicators. Cross-check the VIN and plate against the rate confirmation when a power unit is staged.
Driver and Carrier Vetting
-
Verify CDL, MVR, and Clearinghouse status
Pull MVR, Clearinghouse limited query, and PSP report at hire and annually. Drivers assigned to target-rich loads (electronics, pharma) should have at least 24 months tenure or pass an enhanced background screen.
-
Vet the carrier against FMCSA and CargoNet records
For brokered loads, pull the FMCSA snapshot, check MC age (under 6 months is a fictitious-pickup red flag), confirm the phone and email match the SAFER record, and run the MC through CargoNet's SecureBase or Highway. Reject carriers with recently updated contact info or address mismatches.
Collects list -
Escalate the flagged carrier to safety and security
Route the carrier packet, rate con, and SecureBase findings to the safety director before tendering. Document the override decision if the load is released anyway — fictitious-pickup losses recover faster when the broker can show a written second-set-of-eyes review.
-
Train drivers on the red-zone protocol
Cover the 200-mile rule: no stops within 200 miles of origin on a high-value load. Review fuel-only-at-secured-truckstop policy, no-detour rule, and what to do if approached at a fuel island (do not engage; pull forward; call dispatch).
Load Planning and Dispatch
-
Classify the load risk tier
Tag the BOL commodity against the CargoNet target list: electronics, pharma, tobacco, alcohol, copper, and food/beverage trend highest. Tier-1 loads trigger team drivers, covert tracking, and no-stop dispatch windows.
Collects list -
Plan the route around theft hotspots
Avoid the I-10 / I-95 / I-40 corridor truck stops flagged in the latest CargoNet quarterly report, especially around Atlanta, Dallas, Memphis, Ontario CA, and South Florida. Stage fuel and rest at secured TA / Pilot locations with on-site security.
-
Assign team drivers and a no-stop dispatch plan
For Tier 1 loads, dispatch two drivers so the trailer is never unattended. Pre-fuel the tractor so the first stop is past the 200-mile red zone. Provide secured parking address for the first legal HOS break.
-
Lock the rate confirmation and shipping paperwork
Send the rate con and BOL only through the verified carrier email of record from the FMCSA packet — not a free email address tied to a recently registered domain. Strip the commodity description down to NMFC class on documents handed to the driver.
In-Transit Monitoring
-
Set ELD and trailer geofence alerts
Configure Motive, Samsara, or SkyBitz alerts for: unauthorized stop within 200 miles of origin, door-open events between stops, and deviation from the planned lane by more than 5 miles. Route alerts to the on-duty dispatcher's phone, not just an email inbox.
-
Run check calls at handoff points
Voice call (not text) at first fuel, mid-trip, and arrival. Confirm driver name, location, and seal number against the dispatch record. A driver who hesitates on the seal number or routes the call to an unknown number is a hijack indicator.
-
Confirm secured parking for the HOS break
The driver should park inside a fenced, lit, camera-covered yard or at a CTPAT-recognized secured truckstop. Unmarked rest areas and shopping-center lots are the most common theft locations on Tier 1 loads.
Collects list
Delivery Verification and Information Security
-
Verify seal integrity at consignee
Driver and receiver inspect the bolt seal together before breaking. Photograph the seal number at the trailer doors. A mismatched or re-applied seal is a chain-of-custody break and must be noted on the POD before unloading.
Collects image -
Reconcile piece count and POD
Count against the BOL line-by-line. Note any shortage, damage, or substitution on the POD with the receiver's signature — required to preserve a Carmack Amendment claim. Photos of pallet labels and overall trailer interior support any later cargo claim.
-
Restrict access to shipment data
Limit TMS visibility of high-value loads to dispatcher-on-duty and the safety director. Do not post Tier 1 loads on public load boards (DAT, Truckstop) with the actual commodity in the comments; use NMFC class only.
Incident Response and Recovery
-
Determine whether a theft incident occurred
Trigger this when a check call is missed, a covert tracker pings off-route, a seal is found broken, or a piece count is short. Treat any unexplained 30-minute gap on a Tier 1 load as a theft until proven otherwise.
Collects list -
File the CargoNet and law-enforcement report
File CargoNet within 2 hours — first 24 hours drive recovery rate. Call the local agency where the theft occurred (not the carrier's home jurisdiction) and request a case number. Notify the FBI field office if the load crosses state lines or exceeds $5,000.
Collects text Collects text Collects paragraph -
Notify the cargo insurer and the shipper
Open the claim with the cargo carrier (Great West, Northland, Sentry, etc.) and send the shipper a written incident notice. The Carmack claim window is 9 months from delivery date or expected delivery — clock starts immediately, even before the load is recovered.
-
Run the post-incident review
Safety director walks through the vetting record, dispatch decisions, and tracker timeline with operations. Identify the single control that, if applied, would have stopped the loss — update the SOP and brief drivers and dispatchers at the next safety meeting.
Use this template
Copy it to your account, customize the steps, and run it with your team in minutes.
Browse hundreds of free templates across every team and industry.
Back to template libraryRelated templates
More workflows your team can run.
Run Cargo Theft Prevention Checklist with your team
Customize the steps, assign roles, set a schedule, and keep a complete record for every run.